Hung Phan

1. General
2. FAQ

For Unicast URL Connection:  rtsp://networkvideoserveripaddress/cam0_0 Example: rtsp://192.168.1.100/cam0_0 For Multicast URL Connection:  rtsp://networkvideoserveipaddress/mcam0_0 Example: rtsp://...

• Hung Phan
• August 23, 2023 15:52
• Updated
• 1 follower
• 0 comments
• 0 votes

1. General
2. FAQ

Download SuperLive Plus Mobile App for Android or IOS    1. Enable NAT in the DVR - Go to Main Menu -> Setup -> Network -> NAT interface -> Enable NAT and input the NAT Server - Click Apply to save...

• Hung Phan
• July 25, 2023 23:01
• Updated
• 1 follower
• 0 comments
• 0 votes

1. General
2. FAQ

Required files:   v3.6.16 Software IP Search Tool v1.9.9 is attached below   Before starting, please ensure that you are in the same subnet as the PVM, if you do not know how to configure your NIC ...

• Hung Phan
• July 17, 2023 23:13
• Updated
• 1 follower
• 0 comments
• 0 votes

1. General
2. FAQ

1. On a separate, empty flash drive, download the attached PVM Firmware(See attachment below: V53RUU.bin).2. Remove the power plug from the PVM3. Insert the other flash drive in the USB slot locate...

• Hung Phan
• July 17, 2023 23:12
• Updated
• 1 follower
• 0 comments
• 0 votes

1. General
2. FAQ

1. Open the EDGE browser on your laptop2. Enter the IP address of the camera in the URL box: 192.168.0.1203. Login using the following:username: adminpassword: admin4. If you are prompted to downlo...

• Hung Phan
• July 17, 2023 23:10
• Updated
• 1 follower
• 0 comments
• 0 votes

1. General
2. FAQ

1. Connect the CAT5 crossover cable from the laptop to the RJ45 connector labeled "IPC" on the back of the PVM2. Go into the Network Configuration and write down how your laptop is currently config...

• Hung Phan
• July 17, 2023 23:07
• Updated
• 1 follower
• 0 comments
• 0 votes

1. General
2. FAQ

1. Log onto the device via Web Browser and IP Address. 2. Choose Device Configuration > Device > Local Network3. Configure your IP and Network settings then click Apply to save.  

• Hung Phan
• June 22, 2023 15:36
• Updated
• 1 follower
• 0 comments
• 0 votes

1. General
2. FAQ

Issue:  How to turn off the Motion Alarm Buzzer on an EXMO27IP2W when it is enabled.     Resolution:  1. Press "MENU"2. Press "+" until the menu displays "PVM"3. Press "SOURCE" to select4. Press "S...

• Hung Phan
• June 07, 2023 13:56
• Updated
• 1 follower
• 0 comments
• 0 votes

1. General
2. FAQ

  1. Open the back panel of the PVM 2. Hold the button seen below for 7 seconds and then release it while powered on.  

• Hung Phan
• March 17, 2023 17:30
• Updated
• 1 follower
• 0 comments
• 0 votes

1. General
2. FAQ

The EXCA233 Series cameras, IE or Edge is recommended for usage and management.     When using Edge, you will need to enable IE mode as seen below: 

• Hung Phan
• February 13, 2023 17:31
• Updated
• 1 follower
• 0 comments
• 0 votes